Print This Page
Included in Standard Trim Tab Kit, Standard Performance Tab Kit, SeaDoo Kit, and Bennett Retrofit Kit
5/16" (.79 cm) mounting hardware
Stroke: 2-1/4" (5.72 cm)
Length overall: 12-1/8" (30.80 cm)
Length pin to pin: 11-1/2" (29.21 cm)
Diameter (upper housing): 2-1/2" (6.35 cm)
Mounting hardware: 5/16" ( .79 cm) or Delrin Pin (Part #121)
Part # (Superseded #)
#15054-001 (101-2), 12 Volt w/6' (1.83 cm) cable with Deutsch connector (replacement length)
- Top cap gland seal sheaths the actuator cable outer jacket as well as both internal conductors for maximum waterproofing
- Corrosion proof Vandar mounts
- Stainless steel ram won't flex, even under extreme loads
- Double O-ring for maximum protection
- Ballscrew rotates freely on 12 ball bearings at both ends of its stroke so there's no need for complicated limit switches and clutches
- Self-locking ballscrew locks into position and will not drift
- Precision molded, powdered metal, high alloy gears provide high accuracy, high wear resistance, and high strength for long life
- Tough, high-torque motor easily transfers 750 lbs
- High-impact, ultraviolet resistant nylon 66, 50% glass fiber reinforced thermoplastic housing
- Corrosion proof Vandar cap and mount, stands up to severe loads
Customers most agreed on the following attributes:
from Arlington, Wa on 1/27/2009
Comments about Lenco Lenco 101 Standard Actuator:
Great product, Easy to install and performed well
from Tavernier, FL on 1/19/2009
Comments about Lenco Lenco 101 Standard Actuator:
Very easy to replace. Lenco is a very reliable brand name.
from Orlando on 1/13/2009
Comments about Lenco Lenco 101 Standard Actuator:
This is the actuator for basic model trim tabs from lenco(edged or not). If you can, save the triangular shaped brackets from your original actuator because this does not come with them. Make it easy on yourself and just cut the wire on the new actuator to fit and crimp it to the old wire. I am not a mechanic and installed it in 45 minutes.
from shell beach,la on 10/22/2008
Comments about Lenco Lenco 101 Standard Actuator:
excellent product--- pricing was 50.00 less than local marine store[...] hats off to boaters world
from Charleston, Sc on 9/2/2008
Comments about Lenco Lenco 101 Standard Actuator:
Great ram on a trim tab. No hydrauluic fluid to worry about. Fit and finish is excellent. Comes with necessary mounting hardware. Easy to hookup. Strongly recommend this ram and manufacturer.
from ga on 8/25/2008
Comments about Lenco Lenco 101 Standard Actuator:
Lenco trim tabs. Wow what a deal. [...]
from nj on 8/20/2008
Comments about Lenco Lenco 101 Standard Actuator:
this actuator was vety easy to install and [...] i would recomend this to anyone even beginners could handle this task
from Cape Cod, MA on 8/18/2008
Comments about Lenco Lenco 101 Standard Actuator:
After 7 years/1200 engine hours the gears in the origonal failed, no complaints.
[1 of 1 customers found this review helpful]
from Austin, Texas on 8/4/2008
Comments about Lenco Lenco 101 Standard Actuator:
I have had to replace both original Lenco trim tab activators on my Edgewater 247 within months of one another after less than 4 years of saltwater use. However, the replacement activators were easy to install and work well (note: it is far easier to splice into the old cables rather than run the new cable all the way to the helm).
Comments about Lenco Lenco 101 Standard Actuator:
They work great on my 20ft Hydrosports. Orginals stopped working so replaced both. I bought the boat used so Im not sure how long the first ones lasted but Im happy with this purchase
[1 of 3 customers found this review helpful]
Comments about Lenco Lenco 101 Standard Actuator:
The 101-1 actuator has a 2 1/4 " stroke. It's improperly titled as 1/4'